Canreef Aquatics Bulletin Board

Canreef Aquatics Bulletin Board (http://www.canreef.com/vbulletin/index.php)
-   Reef (http://www.canreef.com/vbulletin/forumdisplay.php?f=8)
-   -   power distribution... (http://www.canreef.com/vbulletin/showthread.php?t=35092)

andestang 09-02-2007 06:42 PM

power distribution...
 
So just curious how people with large systems handle all their electrical demands, such as skimmer(s), reators, heaters, lights, pumps, chillers,frag tank ...... I've been kinda leaning toward getting a seprate fuse panel made/installed. Right now to try and keep things safe and having to reset breakers I have to run off of 4 seperate plug-ins (all seperate circuit breakers) I have to keep in mind what other none reef tank related electrical loads are. I've seen a few scary set-ups with multiple plug-in adapters in one plug-in, just like christmas lights. One does'nt seem to think about this untill time to plug them all up or even after when after time things start to add up.

cav~firez22 09-02-2007 06:55 PM

I ran a fresh line from the breaker to the tank outlet. 20Amp GFDI plug.
then plugged in is a power bar with timers, for alllights,

and the other is a powerbar for all pumps & heater

skylord 09-02-2007 06:57 PM

We just moved into our new house and I had the builder add 2 extra 15 amp circuits and a 60 amp sub panel. Adding the extra is cheap when the electrician is wiring the house anyway.

Scott

mark 09-02-2007 08:37 PM

Already had the breakers plus lots of room in the panel so running 2-15 GFI breaker circuits, one for upstairs (CL pump, fluorescents) and second for downstairs equipment (main pump, skimmer) logic being if a one breaker accidentally trips, I still have some water movement. Have a third cct on a regular breaker feeding first a GFI receptacle then others downstream but main load is the MHs.

Other equipment such as pumps and heater for mixing water, datalogger, CO2 solenoid etc is also tied to the above GFI ccts where convenient.

untamed 09-02-2007 11:42 PM

Sorry...I ran 4 dedicated 15A circuits right from the main box to the tank room. At little planning on power usage helped me decide what to plug into what circuit so that if any individual circuit goes, it doesn't matter too much.

surgeonfish 09-03-2007 03:43 AM

When we did our reno, I also ran separate lines to the tank and put in another line and breaker box in the tank room downstairs.

scsi 09-03-2007 09:15 AM

I'v been considering this problem as well. Right now I'm using 3 different outlets, but one of them is connected to a huge power strip where I have about 8 things comming off it..... That can't be good

DJKoop 09-03-2007 02:43 PM

I was doing renovations anyways so I had the electrician throw in 2 more 15A breakers for the tank and a ton of plugs.

andestang 09-03-2007 03:29 PM

Quote:

Originally Posted by cav~firez22 (Post 269417)
I ran a fresh line from the breaker to the tank outlet. 20Amp GFDI plug.
then plugged in is a power bar with timers, for alllights,

and the other is a powerbar for all pumps & heater

Thats what I wanted to do but my breaker box has no spare openings left to add any new breakers. :(

Chin_Lee 09-03-2007 04:47 PM

IF i had to do it again, I would run my circuits similar to that of my kitchen. 20 amp circuit for the top plugs and another 20 amp circuit for the bottom plugs. Just make sure you break off the brass connector between the two plugs that comes standard when you buy them otherwise you will get some sparks flying when you power them up.


All times are GMT. The time now is 01:29 PM.

Powered by vBulletin® Version 3.7.3
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.