|
I got the calcium reactor today. For some reason they shipped the PF601S instead of the PF600. That's no problem, so long as it fits under the stand. I assume it will but I won't know until I get the skimmer & kalk mixer. I might have to relocate the CO2 tank, but I was thinking of doing that anyways. This sure is a nice unit, looks very well built.
http://img.photobucket.com/albums/v6...k/DSCN0271.jpg |
Wow, like the progress and equiptment so far ! Where did you get the the DJ center & Aquatronica powerbars. Was thinking of doing something like that.
|
What is the price tag on that UV if you don't mind me asking Dave?
|
Quote:
|
Quote:
|
There isn't a lot of space above the sump for a refugium light. The best I could find is a Coralife 24" Aqualight. It fits perfect, and has two 65w PC bulbs... even a fan.
http://img.photobucket.com/albums/v6...k/DSCN0272.jpg The tank is now built, is curing & being water tested. I hope it will ship in a week or so. The skimmer & kalk mixer should be coming soon. The rest of the equipment will come with the tank. Next week I plan to get most of the plumbing done. The holes are drilled on the tank and I've got the details of where they are, pictures to support it. So I should be able to get the plumbing supplies now. I figure I'll drill the plywood & styro that the tank sits on and then drill the shelf below and just drop the plumbing straight down into the sump. I'll also have to route one pipe over to the skimmer and then to the sump but the returns can come straight up to the tank as well. I want to do this now so I can figure out where I can mount the UV since it will be strapped to the underside of the shelf. I'm also going to get the wood for the shroud for the tank stand. I'm leaning towards birch plywood. It's very smooth & flat and should look great. I want to have 3 separate doors to the stand, one for each section & two sides. The height of the wood will be 2" taller then the stand so it will cover the plywood, styro and the bottom pane of glass. It will also extend 1" beyond the back edge of the stand to keep my cat out of there. I want to make cutouts on the doors for the DJ panel, Aquatronica controller & Tunze controller. I figure if I don't I'll just be constantly removing the boards to see what's going on. |
Long post here, lots of pics so sorry to dialup folks. I had some time & I wanted to determine whether I could do the aquascaping without PVC, acrylic rods or cement. So I taped off the tank inside dimensions, laid down the starboard and pretended that I had my tank. Call it boredom, planning or just impatience waiting for the tank. Insanity is more like it. I started out wanting a couple of lopsided, different sized islands and ended up with a bit more then that. I'm trying to avoid the "wall of rock" look that I've seen, as well as trying to keep the rock away from the glass to allow cleaning of all sides. I may have come closer to the wall-look then I want but it's my first attempt and I think it's pretty good. This rock will certainly provide a lot of places for coral placement. Unfortunately I don't have that much floor space to lay it out so I am not able to get any pics from the full frontal look of the rock. Here's the best I could do. I'm not tied to this look so feel free to voice your opinions...
Looking to the right side from the front... http://img.photobucket.com/albums/v6...k/DSCN0300.jpg More detail of front, right end... http://img.photobucket.com/albums/v6...k/DSCN0301.jpg Same end, different angle... http://img.photobucket.com/albums/v6...k/DSCN0304.jpg Left end while looking to the right... http://img.photobucket.com/albums/v6...k/DSCN0303.jpg Looking towards the left side from the front... http://img.photobucket.com/albums/v6...k/DSCN0308.jpg Gap between right & left side, might remove the joining rock & leave empty... http://img.photobucket.com/albums/v6...k/DSCN0309.jpg Another angle of left side... http://img.photobucket.com/albums/v6...k/DSCN0306.jpg Left end... http://img.photobucket.com/albums/v6...k/DSCN0305.jpg When it comes to assembling this in the tank I plan to do it this way again and get it the way I want it and then move it piece by piece into the tank room & into the tank. It's much easier to manipulate the rock & find the best fit this way rather then in a glass tank. And this rock fit together very solidly, without anything holding it together other then its own weight. Any comments? |
that looks awesome davec. how sturdy are the pieces togther without using any compound?
|
Very sturdy. I tried pushing them over with reasonable force & they didn't budge. Still not sure I'd trust that in a glass tank. I might zip tie the bigger pieces.
|
What type of rock is it?
|
| All times are GMT. The time now is 11:43 AM. |
Powered by vBulletin® Version 3.7.3
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.