Canreef Aquatics Bulletin Board

Canreef Aquatics Bulletin Board (http://www.canreef.com/vbulletin/index.php)
-   Reef (http://www.canreef.com/vbulletin/forumdisplay.php?f=8)
-   -   anyone piped their tank with Aryclic tubing or Clear PVC? (http://www.canreef.com/vbulletin/showthread.php?t=63123)

Milad 04-08-2010 06:31 AM

damn you untamed and your knowledge
I rejigged it and put it 2 inches below the water level
for my tank it would be 15gallons if the holes pluged and the check valve jammed

I also changed out the tunze 6205 for two tunze 6105s

Watcha guys think?
http://dl.dropbox.com/u/2361330/aq2tunze6105.jpg

kien 04-08-2010 01:29 PM

Looking good :-) You can eliminate one bend in your return line if you run the line closer to that outlet side of your sump and tank instead of right smack dab in the middle. Running it in the middle like that probably won't work too well anyway because that line will probably run into the skimmer. That is unless that end of the sump (closest to the overflow) houses the return section of the sump and not the skimmer.

kinda like this..
http://i1002.photobucket.com/albums/...g?t=1248761945

Oh, and if you are going to put two powerheads there I would consider making the overflow box smaller. Leave enough room on either side of the overflow box for the powerheads. In the future if you ever decide to go vortex they won't work at that end of the tank with your overflow box the way it is. Plus, adjusting the powerheads up and down or removing it for cleaning will be a royal pain in the ass if you have to fish out that magnet out of your overflow box.. trust me, been there tried that! I suppose you could put the magnets on the display sides of the tank. That wouldn't be too bad I guess.

Milad 04-08-2010 02:59 PM

What's a vortex? Also why would it be hard to adjust if the magnets are inside the overflow? I figured it would hide it all. Was even going to run the wires through overflow. If I made the width of the overflow skinnier and placed the heads on the glass wouldn't the wall of the overflow partially block the current?

Also you think the two powerheads are good enough controlled by a apex or should I get the 6205.

Thanks for all the help btw. Just want to get the correct parts the first time.

hillegom 04-08-2010 04:10 PM

actually vortech. There are two available, the mp20 and mp40. You can use one or two in your tank. Pricy, but very good.
http://www.youtube.com/watch?v=w15wOWcZ7Mo

Milad 04-08-2010 05:03 PM

I was looking at those but they are too loud for me

Are they actually an upgrade from the tunze 6105s?

Quote:

Originally Posted by hillegom (Post 508890)
actually vortech. There are two available, the mp20 and mp40. You can use one or two in your tank. Pricy, but very good.
http://www.youtube.com/watch?v=w15wOWcZ7Mo


StirCrazy 04-08-2010 11:56 PM

Quote:

Originally Posted by Milad (Post 508698)
Im trying to find a way to pipe the return on my tank as aesthetically pleasing as possible. I have to bring 6 feet of pipe over the length of the tank and I really do not want to build a canopy for it. so.... I had a dream, a dream to use clear tubing and have it sit inside the top or just above the glass and run the length of the tank.

Has anyone ever done this? If so, is there a downside? could it get dirty inside?

The clear PVC is twice the cost of the Acrylic and but the problem is im not sure if I can glue the PVC to the Acrylic because they only make PVC elbows.

you can use weldon 16 or 40 I believe to join them, problem is it will be coated with algae in no time and look bad. and the fact that it is close to 80X more expensive than just using regular PVC

Steve


All times are GMT. The time now is 10:49 AM.

Powered by vBulletin® Version 3.7.3
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.